TMI MULTIMEDIA TMI336 Card Type Modem Chip Set PC-TEL I/O Options Line in, line out Maximum Modem Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103A/212A V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34, V34+ Fax Modulation Protocol V.17, V.21, CH2, V.27ter, V.29 Error Correction/Compression MNP5, V.42bis Fax Class Class I Data Bus 8-bit ISA Card Size Half-length [Image] CONNECTIONS Function Label Function Label Line out CN1 Line in CN2 PNP SELECTION Setting JP5 JP9 PNP disabled Closed Pins 1 & 2 closed PNP enabled Open Pins 2 & 3 closed SUPPORTED COMMAND SET Basic AT Commands AT, A/ A, E, H, M, O, P, Q, S, T, V, W, X, Y, Z &C, &F, &G, &P, &W, &Y, &Z Extended AT Commands \A, \B, \G, \L %C, %L, %Q #CID AT Voice Commands #BDR, #CLS, #MDL?, #MFR?, #TL, #REV?, #RG, #SPK, #VBS, #VBT, #VLS, #VSR #VRA, #VRX, #VSD, #VSP, #VSS, #VTX, #VBQ?, #VCI?, #VRN, #VSK, #VTD, #VTS S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S18, S25, S30, S32, S33 S38, S91 Note: See MHI Help File for full command documentation. Proprietary AT Command Set AUTO-MODE DETECTION Type: Configuration Format: AT [cmds] Nn [cmds] Description: Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. Command Function N0 Auto-mode detection disabled N1 Auto-mode enabled. Modem will answer at highest available line speed COMMUNICATION PROTOCOLS Type: Configuration Format: AT [cmds] Bn [cmds] Description: Selects the communication protocol for data calls Note: The B command allows the simultaneous selection of more than one suffix, enabling multiple protocols. Command Protocol B0 ITU-T V.22 at 300 or 1200bps B1 Bell 212A at 300 or 1200bps B2 ITU-T V.23 at 75 or 1200bps CONFIGURATION PROFILES Type: Immediate Format: AT [cmds] &V [cmds] Description: Displays active and stored configuration profiles Command Function &V0 Displays active configuration profiles &V1 Displays stored configuration profiles &V2 Displays stored telephone numbers DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR high only while modem is handshaking or connected DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Command Function &D0 DTR is assumed on &D1 DTR toggle causes online command mode &D2 Normal DTR operations &D3 Resets on receipt of DTR DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function D Modem off-hook and waits for dial tone up to the time specified by S7 register DL Re-dial last number DR Answer mode enabled; originate mode disabled following handshake initiation. DS=n Dial stored telephone number n DW Dialing resumed following dial tone detection D, Dialing paused for amount of time specified in S8 register Dmn ATDmn will dial a phone number where m is a modifier: L, W, , , :,@,! Or S. It will dial the telephone number n. D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. D^ Turns on 1300Hz calling tone FLOW CONTROL Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Enables flow control options &K4 XON/XOFF flow control enabled &K5 Transparent XON/XOFF flow control enabled &K6 Unidirectional XON/XOFF flow control enabled REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports product code I1 Reports hardware variation I2 Reports internal code I3 Reports software revision number I4 Reports product feature listing SPEAKER VOLUME Type: Configuration Format: AT [cmds] Ln [cmds] Description: Controls speaker volume Command Function L0 Speaker disabled L1 Low volume setting L2 Low volume setting L3 Low volume setting Note: Hardware currently limits volume adjustment to on/off TEST MODES Type: Immediate Format: AT [cmds] &Tn Description: Selects test options Command Function &T0 End current test &T1 Begin local analog loopback test TRELLIS CODING Type: Immediate Format: AT [cmds] &U [cmds] Description: Enables/disables trellis coding Command Function &U0 Enable trellis coding &U1 Disable trellis coding Extended AT Command Set AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD Type: Configuration Format: AT [cmds] %En [cmds] Description: Controls auto-retrain mode and fallback/fall-forward Command Function %E0 Auto-retrain disabled %E1 Auto-retrain enabled %E2 Auto-retrain and fallback enabled %E3 Auto-retrain and fast hang up enabled BREAK TYPE Type: Configuration Format: AT [cmds] \Kn [cmds] Description: Configures action of break signal Command Break from DTE Break from DTE Break received during NORMAL or during DIRECT from remote modem MNP mode mode during NORMAL mode \K0 Online command Send break to Buffers cleared, mode enabled, remote modem, break sent to DTE send no break to online command remote modem mode enabled \K1 Break sent to Send break to Buffers cleared, remote modem and remote modem, break sent to DTE buffered cleared online command mode enabled \K2 Online command Send break to Break sent mode enabled, remote modem immediately to DTE send no break to remote modem \K3 Send break to Send break to Break sent remote modem remote modem, immediately to DTE immediately online command mode enabled \K4 Online command Send break to Break sent with mode enabled, remote modem received data to send no break to the DTE remote modem \K5 Send break with Send break to Break sent with transmitted data remote modem received data to the DTE CONNECT MODE Type: Configuration Format: AT [cmds] \Nn [cmds] Description: Controls the type of connection the modem will operate in Command Function \N0 Normal mode enabled \N1 Direct mode enabled \N2 Reliable mode enabled \N3 Auto-reliable mode enabled \N4 LAPM reliable mode enabled \N5 MNP reliable mode enabled COUNTRY CODE Type: Configuration Format: AT [cmds] %I=n [cmds] Description: Loads a set of selected country parameters. Command Function n=1 USA parameters n=2 France parameters n=3 Germany parameters n=4 Italy parameters n=5 Sweden parameters n=6 UK parameters n=7 Japan parameters n=8 Australia parameters n=9 Spain parameters n=10 Taiwan parameters n=11 Singapore parameters n=12 Korea parameters n=13 Switzerland parameters n=14 Norway parameters n=15 Netherlands parameters n=16 Belgium parameters n=17 Canada parameters n=18 Ireland parameters n=19 Portugal parameters n=20 Poland parameters n=21 Hungary parameters n=22 Finland parameters DYNAMIC CPU LOADING Type: Configuration Format: AT [cmds] %Nn [cmds] Description: Selects auto-fallback/fall-forward Command Function %N0 Dynamic CPU loading disabled %N1 Dynamic CPU loading not to exceed 10% %N2 Dynamic CPU loading not to exceed 20% %N3 Dynamic CPU loading not to exceed 30% %N4 Dynamic CPU loading not to exceed 40% %N5 Dynamic CPU loading not to exceed 50% %N6 Dynamic CPU loading not to exceed 60% %N7 Dynamic CPU loading not to exceed 70% %N8 Dynamic CPU loading not to exceed 80% %N9 Dynamic CPU loading not to exceed 90% PTT TESTING Type: Configuration Format: AT [cmds] %Pn [cmds] Description: Allows user to initiate a series of signals necessary for PTT approval Command Function %P00 - %P09 DTMF digits 0-9 %P10 DTMF digit A %P11 DTMF digit B %P12 DTMF digit C %P13 DTMF digit D %P14 DTMF digit * %P15 DTMF digit # %P16 V.21 channel 1 mark 980Hz %P17 V.21 channel 2 mark 1650Hz %P18 V.23 reverse channel mark 390Hz %P19 V.23 forward channel mark 1300Hz %P20 V.22 originate %P21 V.22bis originate %P22 V.22 answer %P23 V.22bis answer %P24 V.21 channel 1 space 1180Hz %P25 V.21 channel 2 space 1850Hz %P26 V.23 reversed channel space 450Hz %P27 V.23 forward channel space 2100Hz %P28 V.32 at 9600bps %P29 V.32bis 14400bps %P30 Off-hook %P31 V.25 answer tone 2100Hz %P32 Guard tone 1800Hz %P33 V.25 calling tone 1300Hz %P34 Fax calling tone 1300Hz %P35 V.21 channel 2 1650Hz %P36 V.27ter 2400bps %P37 V.27ter 4800bps %P38 V.29 7200bps %P39 V.29 9600bps %P40 V.17 7200bps long train %P41 V.17 7200bps short train %P42 V.17 9600bps long train %P43 V.17 9600bps short train %P44 V.17 12.0Kbps long train PTT TESTING (CONT.) %P45 V.17 12.0Kbps short train %P46 V.17 14.4Kbps long train %P47 V.17 14.4Kbps short train %P48 V.34 2400bps modulation %P49 V.34 4800bps modulation %P50 V.34 7200bps modulation %P51 V.34 9600bps modulation %P52 V.34 12.0Kbps modulation %P53 V.34 14.4Kbps modulation %P54 V.34 16.8Kbps modulation %P55 V.34 19.2Kbps modulation %P56 V.34 21.6Kbps modulation %P57 V.34 24.0Kbps modulation %P58 V.34 26.4Kbps modulation %P59 V.34 28.8Kbps modulation %P60 V.32bis 9600bps modulation %P61 V.32bis 12.0Kbps modulation %P62 Bell 212A originate 1200bps %P63 Bell 212A answer 1200bps %P64 Bell103 originate mark 1270Hz %P65 Bell103 originate space 1070Hz %P66 Bell103 answer mark 2225Hz %P67 Bell103 answer space 2025Hz %P99=n 0<=n<=23 Range: 0-23 Unit: (150Hz) RESULT CODES SENDING Type: Configuration Format: AT [cmds] *Qn [cmds] Description: Sends CONNECT xxxx result codes to the DTE Command Function *Q0 Send CONNECT xxxx result codes to the DTE when an invalid TIES escape sequence is detected after the K response has been sent *Q1 Does not send CONNECT xxxx result codes to the DTE when an invalid TIES escape sequence is detected after the K response has been sent S REGISTERS BAUD RATE Type: Register Format AT [cmds] S35=n [cmds] Description: Sets the maximum allowable baud rate for V.34 Command Function S35=0 Speed of last connection S35=1 2400bps (N/A) S35=2 2743ps (N/A) S35=3 2800bps S35=4 3200bps S35=5 3429bps (N/A until V.34bis) CONNECTION FAILURE CODES Type: Register Format AT [cmds] S86? [cmds] Description: Reports codes which correspond to the possible causes of a connection failure Value Meaning 0 Normal hang up 4 Carrier signal lost 5 No error-control detected for remote modem during feature negotiation 6 Remote modem failed to respond to feature negotiation 9 No common protocol found 12 No failure - remote modem disconnected normally 13 Remote modem failed to respond after 10 re-transmissions same message 14 Violation of negotiated protocol caused failure 15 Negotiated compression failed 20 Hang up by inactivity time out DCE LINE SPEED Type: Register Format AT [cmds] S37=n [cmds] Description: Sets the maximum allowable data exchange rate attempted during handshake process. Command Function S37=0 Speed of last connection S37=1 75bps S37=2 110bps S37=3 300bps S37=4 600bps S37=5 1200bps S37=6 2400bps S37=7 4800bps S37=8 7200bps S37=9 9600bps S37=10 12.0Kbps S37=11 14.4Kbps S37=12 19.2Kbps S37=15 28.8Kbps V.34 DATA RATE Type: Register Format: AT [cmds] S34=n [cmds] Range: 0-8 (2400 baud) 1-10 (3000 baud) 1-11 (3200 baud) 1-13 (3429 baud) Unit: ASCII Description: Sets the maximum bit rate for V.34